I have both NEW PRECISION "MASTERING-GRADE" ATR 100 series parts
and USED ATR 100 series parts- generally in very good condition and FULLY TESTED
| Email us here to order |
you must put the word Ampex or MCI or Studer or Otari into the subject line !!!
Brand NEW ATR 100 series PARTS !!!
MASTERING GRADE New Polyurethane unit
Complete with Precision Mounted Glass Disc Encoder
Finest grade made
Cost: $ 420 (requires trade-in of your old unit)
Tape-Lifter Arm Sleeves
Precision Milled
these slip over the existing lifter arms and give you a beautiful smooth surface
Cost $ 45.00 per Sleeve
Class AAA7 bearings for Tension Arms
for both 1/4 inch and 1/2 inch machines
These are MASTERING-GRADE bearings - the best there is!!
Prices run 25.00 to 50.00 per bearing and include the correct spacers
COMPLETE Half-Inch Conversion package:
Headstack with a full set of good used 1/2 inch two track heads
PLUS the two 1/2 inch guides
Cost: $ 1,700 for the complete set
heads are being sent off to Sprague Magnetics for a head report
NEW SAKI 1/4 inch 2 track heads !!!!
NEW ATR 102 1/4 inch Heads - Saki 1/4 inch 2 track RECORD head - new unused !!
Cost: $ 350
NEW ATR 102 1/4 inch Heads - Saki 1/4 inch 2 track REPRODUCE head - new unused !!
Cost: $ 350
NEW AMPEX ATR 102 1/4 inch 2 track ERASE HEAD - new unused !!!
Cost: 275
We also sell NEW FLUX MAGNETICS heads for Ampex ATR 100 series tape recorders!
-- 1/4 inch 2 track -- 1/2 inch 2 track -- 1/2 inch 4 track
Prices for 1/4 inch 2 track ATR 102 heads...
Erase (new) 650.00
Record (new) 745.00
Repro (new - 'normal' head) 650.00
Repro (new - 'Extended Low Frequency' head) 800.00
Prices for 1/2 inch 2 track ATR 102 heads
Erase: 625.00
Record: 745.00
Reproduce: 745.00
Extended Low Frequency Reproduce head: 825.00
best is the Special Extended Low Frequency Repro head...
a MUST for all Mastering Facilities !!!!!
Used parts further down this page....
The Extended Low Frequency Repro Head is a must for your machine
it extends the low end and makes the low end as flat as it can be....
which is what you want in any Mastering Machine
Also Mastering Engineers should have 2 extra Audio Cards on hand and pre-set-up
for IEC-1 equalization - so you can switch quickly between NAB eq and IEC-1 eq tapes at 15 ips
by swapping audio cards rather than pulling the cards out, changing the EQ switches,
re-aligning the cards to IEC-1, then switching the EQ switches back and re-aligning to NAB EQ...
the first time you forget to set the EQ to the proper equalization - and the word gets around -
and it will... you will be laughing stock of Mastering Engineers and likely fighting that reputation for years and years.
It's not worth the risk. Buy a couple spare Audio Cards and set them for IEC-1, label them "IEC-1"
Then make a point that you
1) know the difference between IEC-1 and NAB EQs
2) have the right audio cards and easily can switch between NAB and IEC-1
3) always do the correct thing rather than try and sneak by incorrectly.
Then you can laugh at those idiots who don't know IEC-1 from NAB from their asses
because you are a PRO and not a wana-be !
by the way this means you HAVE to have BOTH an NAB and a IEC-1 15 ips Test Tape !!!
and yes I sell brand new Alignment Tapes !!!
HIGH-QUALITY USED ATR 100 Series PARTS
take a look at the list below and see if I've got the parts you need!
can be also used as a remote control by installing an extension cable
Good quality used Control unit.... looks fine, buttons all work and feel like new!
List for a normal used one $ 300 - 495
the best one I have - cost: $ 250.00 2nd best cost: $ 215
ATR 100 series Multi-Point Search to Cue Remote Cable !!! RARE !!!
use this to connect up the Multi-Point Remote to your ATR 100 !!
Cost $ 100
ATR 100 series Audio I/O Module
Looks like new and works great ! Nice VU meter !!!
Normally these cost $ 250 - 375 per unit !!! your cost: $ 200.00
ATR 100 series COMPLETE POWER SUPPLY
Yep. a complete power supply - transformer, voltage regulator card, all the trimmings !!!
this beast is HEAVY so shipping will be costly.... but if your power supply has repeatedly
gone bad, this is the most cost-effective way to bring it back to normal spec
Cost: $ 250 !!
ATR 100 series Reel Motor
Cost: $ 200
ATR 100 series complete transport frame
This is just the deck-plate and card cage -
no cards - no sensors - no guides - no motors cost: $ 200
ATR 100 series Tension Arm Sensors
These are the lower units -
Cost $ 90 per unit
Original AMPEX ATR 102 Roll Around STAND !!!
For all ATR 100 series machines... very rare !!
Cost: $ 225
ATR 100 series CARDS:
Currently I'm out of stock on any ATR 100 Transport
or Audio Cards - - -
| Email us here to order |
you must put the word Ampex or MCI or Studer or Otari into the subject line !!!
------ Other AMPEX ATR 100 series Parts Suppliers ------
If I don't have what you need... The ONLY people I know of who have a better selection of ATR 100 parts are
John Austin at Sprague Magnetics - Michael Spitz at ATR Service - Jeff Gilman at PrecisionMotorWorks
and George at Athan Corp.
Links to all are below....
Tell them 'Goreski' send you!!!
For Ampex ATR 100 series Parts and tape recorder heads and relapping....
Sprague
talk to John Austin... and tell him 'Goreski' sent you !
For Ampex ATR 100 series Parts (102/ 104/ 108 / 116 / 124)
ATR Service
talk to Michael Spitz... and tell him Goreski sent you !
Precision Motor Works
talk to Jeff Gilman... and tell him Goreski sent you !
Athan Corp
talk to George... and tell him Goreski sent you !
>>>>>NOTE that prices are ALWAYS subject to change....
=============================================
| Sprague |
| ATR Service |
| Precision Motor Works |
| Athan Corp |
>>>>>NOTE that prices are ALWAYS subject to change....
|
|